PRESSURE SENSORS

Chicago Stainless Equipment offers several different pressure sensors. Sanitary or non-sanitary, with or without a display, with or without switching capabilities.  Please refer to the table below for information on each series we offer.

Pressure Sensors
Sanitary Pressure Transmitters Sanitary Pressure Transmitter with Display PI27 Series: 3 wire loop powered sanitary pressure transmitter and switch with a 4 digit alphanumeric display, 4 to 20 mAmp output, zero and span adjustable. Quickly connects with a water tight standard M12 industrial connector. Easily programmed with push buttons on the sensor without the need for a reference gauge. Available with Tri-Clamp, DIN, or Varinline fittings. Can be used to monitor process pressure or for tank level measurement with an accuracy of +/- 0.2% of span. Units of measure and switching points can be quickly and easily changed between psi, bar, mbar, kPa, MPa, inch of water, or percent of span. Available in ranges from 15 psi vacuum up to 363 psi.  3-A, CE, UL, FDA and EHEDG Certified.
Specifications | Ordering Information | Operating Instructions | Brochure
Sanitary Pressure Transmitter without Display PM20 Series: 2 wire loop powered sanitary pressure transmitter without a display, 4 to 20 mAmp output, zero and span adjustable.  Quickly connects with a water tight standard M12 industrial connector.  Easily programmed with EPS interface (sold separately).  Available with 1½" or 2" Tri-Clamp or SMS fitting.  Can be used to monitor process pressure or for tank level measurement with an accuracy of +/- 0.6% of span.  Will withstand process temperatures up to 125°C.  Available in ranges from 15 psi vacuum up to 363 psi.  3-A, CE, UL, FDA and EHEDG Certified.
Specifications | Ordering Information | Operating Instructions
Industrial Pressure Transmitters Industrial Pressure Transmitter with Display PN Series: 2 wire loop powered industrial pressure transmitter and switch with a 4 digit alphanumeric display, Dual PNP / NPN Switching or PNP/ NPN Switching and 4 to 20 mA / 0 to 10 VDC analog output. Zero and span adjustable. Quickly connects with a water tight standard M12 industrial connector. Easily programmed with push buttons on the sensor. Available with 1/4" male NPT or 1/4" female NPT process connection. Can be used to monitor process pressure or for tank level measurement with an accuracy greater than +/- 0.4% of full range. Units of measure and switching points can be quickly and easily changed between psi, bar, mbar, kPa, MPa, inch of water, or percent of span. Available in ranges from 14.5 psi vacuum up to 8700 psi. CE and UL Certified.
Specifications | Ordering Information | Operating Instructions
Industrial Pressure Transmitter without Display PM26 Series: 2 wire loop powered industrial pressure transmitter without a display, 4 to 20 mAmp output, zero and span adjustable.  Quickly connects with a water tight standard M12 industrial connector.  Easily programmed with EPS interface (sold separately).  Available with ¼" or ¾" male NPT process connection.  Can be used to monitor process pressure or for tank level measurement with an accuracy of +/- 0.6% of span.  Will withstand process temperatures up to 125°C.  Available in ranges from 15 psi vacuum up to 363 psi.  CE and UL Certified.
Specifications | Ordering Information | Operating Instructions
Industrial Pressure Transmitter PX32 Series: 2 wire loop powered industrial pressure transmitter without a display, 4 to 20 mAmp output, zero and span adjustable.  Our inexpensive series quickly connects with a water tight standard M12 industrial connector.  This series is not programmable.  Available with ¼"  male NPT process connection.  Can be used to monitor process pressure or for tank level measurement with an accuracy of +/- 0.75% of span.  Will withstand process temperatures up to 90°C.  Available in ranges from 14.5 psi vacuum up to 3000 psi.  CE and UL Certified.
Specifications | Ordering Information | Operating Instructions
Industrial Pressure Transmitter/Switch Industrial Pressure Transmitter/Switch with Display PG27 Series: Loop powered sanitary digital and analog pressure gauge with transmitter/switch and a 4 digit alphanumeric display. This unit is an analog pressure gauge with a pointer, a digital pressure gauge with a 4 digit display, a pressure switch with PNP/NPN switching, and a pressure transmitter with a 4 to 20 / 20 to 4 mA output. Quickly connects with a water tight standard M12 industrial connector. Easily programmed with push buttons on the sensor. Can be used to monitor process pressure or for tank level measurement with an accuracy greater than ± 0.2% of full scale and it will withstand process temperatures up to 80°C. Available with Tri-Clamp, DIN, or Varinline process connections. Units of measure and switching points can be quickly and easily changed between psi, bar, mbar, kPa, MPa, inch of water, or percent of span. Available in ranges from 14.5 psi vacuum up to 580 psi. CE and UL Certified.
Specifications | Ordering Information | Operating Instructions

Copyright © 2024 Chicago Stainless Equipment, Inc. All rights reserved.